Happy 2010!

HAPPY NEW YEAR.  This weekend we are offering 15% off all purchases from our web site Harrington's Glass Art Molds And Supplies (not eBay). Use coupon code:  HNY2010

Offer expires Midnight (Monday), January 4, 2010 and is good once per customer.

CYPER MONDAY SALE 11/30/09

Cyber Monday 11/30/09. Use code: CBM2009 at checkout to get 10% off all your purchases. Code is good 1 time per customer and cannot be combined with other offers. Coupon code is good today only and must be entered at checkout to receive the discount. You must register to use the code if you are not already a registered customer.

QUICK GLASS CUTTING TIPS

The table you are cutting on must be flat.

Pressing too hard with the glass cutter will produce imperfections along the freshly cut glass edge. Press just hard enough to make an even, steady noise and a consistent score line.

Here is a fast way to cut small pieces. The only tools you will need are a glass cutter and straight edge. First, make all your score lines on the glass. Then turn the glass over and tap out the pieces.

When making a long cut, do not lift the glass as you break it with breaking pliers. Lifting can put a slight bow in the glass, which causes it to separate erratically. Instead, leave the glass flat on the table, pull a little out from the edge, and break it with piers.

After scoring, use breaking pliers to separate a narrow piece of glass.

(Kiln Pointer from Paragon)

ADDING SILVER TO FUSED GLASS

If you ever file a fired silver clay piece for final shaping, do not discard the filings. They are beautiful when fused into glass jewelry.

Catch the filings with a piece of paper. After you have finished shaping the silver piece, fold the paper in half. Tap it so the silver powder falls into the fold. Then pour the filings from the corner of the fold onto a piece of clear fusible glass.

When fired between layers of clear glass, the silver will retain its original color and sheen, or it will turn yellow-gold.

(Kiln Pointer from Paragon)

USING FUSEWORKS MICROWAVE DECALS IN AN ELECTRIC KILN

Fuseworks Decals may be used in electric or microwave kilns. The firing schedules shown below are only a point of reference for the decals in an electric kiln. You may need to adjust temps and timing, based on your kiln. (These instructions were supplied by a vendor for Fuseworks Decals.)

FUSING Schedule
1. 750F per hour to 800F – Hold 1 minute
2. As fast as possible to 1350F – Hold 15 minutes
3. As fast as possible to 1000F – to room temp.

SLUMPING Schedule
1. 300F per hour to 1000F - hold 15 min
2. 300F per hour to 1325F - hold 15 min
3. As fast as possible to 960F - hold 30 min

HOW TO DRILL BISQUE FOR GLASS SLUMPING MOLDS

Not all molds that make great slumping molds are pre-drilled because they were designed to be used for ceramics. You can drill holes in the molds that would be suitable for slumping. Be sure you examine the mold for crevices and areas that would keep you from removing your glass without breakage.

Holes should be drilled in bisque to allow air to release while the glass is slumping. It is recommended to use a 1/8” or 3/16” Carbide Tip Drill Bit when drilling bisque for slumping. To avoid cracking or uneven slumping it is important to drill holes in any bisque piece that you use to slump glass.

TO DRILL: Position the holes evenly on the surface of the bisque. The number of holes to drill depends on the size of the piece. Also, if the bisque piece has a foot, you may want to file the foot in several places to create an air channel to help air escape from under the glass.

So, how many holes should you drill? This chart is a guideline to help you decide:

WHICH SIDE OF DICHROIC GLASS HAS THE COATING?

It is not always easy to tell which side of clear glass has the dichroic coating. The coated side is the side that has a rougher texture.

Use any pointed object such as a pencil, toothpick or even your fingernail and hold this object to the glass. If the reflection touches the object, then this is the coated side of the dichroic glass. A space between the reflection and the object means this is not the coated side.

NEW RECOMMENDED ANNEALING CYCLE FOR BULLSEYE GLASS

New Recommended Annealing Cycle for Bullseye Glass
Save time and energy. Anneal thick slabs at 900 degrees.

As of June 2009, Bullseye has changed its chart for annealing thick slabs. Specifically, the recommended anneal soak temperature has been lowered from 960°F/516°C to 900°F/482°C.

Why the change?
For several years we have used the new 900°F/482°C soak temperature for everything from simple fused pieces to large-scale castings, with tremendous success. We now consider it more practical than 960°F/516°C—especially on larger, thicker projects—for two reasons:

1. More effective: After the stress has been relieved by holding the glass at an anneal soak temperature of 900°F/482°C, the glass cools over a shorter span of temperature in which annealing stress could be introduced than it would be if held at 960°F/516°C.
2. More efficient: It takes less time to cool over a shorter span of temperature.

What about past work that has already been made with the anneal soak at 960°F/516°C?
There is no need to worry about this work. Effective annealing has been and can be accomplished when the anneal soak is performed at 960°F/516°C. It just takes longer, especially with projects that are thicker or very large.

If your past projects have been successful using cycles with an anneal soak at 960°F/516°C, you may continue to use that temperature. Or, if you wish to save time, you can revise your cycle to have an anneal soak at 900°F/482°C.

Why can most works be annealed successfully with either anneal soak temperature?
This is because when annealing glass, the most important factor is not the temperature at which one performs the anneal soak (within reason). Rather, the most important factor is the ability to achieve uniform temperature throughout the body of glass during the anneal soak and subsequently cool the glass in such a manner that it does not develop more than a 10°F/5°C temperature difference throughout the body of glass during the first anneal cool to 800°F/427°C. For more information on this topic, see Bullseye’s TechNotes 7: Monitoring Kiln Temperatures for Successful Annealing.

Where can the new Annealing Chart for Thick Slabs, and TechNotes 7: Monitoring Kiln Temperatures for Successful Annealing be found?
Click here to download the new annealing chart.
Click here to download TechNotes 7.

WELCOME!

WELCOME to our corner of cyberspace! We thought a blog would be so much more fun than an email newsletter. We love GLASS and hope your love of working with glass will bring you back here again and again. We will be bringing you project ideas, tips and instructions, product reviews, industry news and information, thoughts and hopefully a lot of friendship with our blog.

We carry a large variety of molds, Dichroic and fusible glass, findings, studio supplies and more. We have new stock and items arriving several times each week, and we are happy to take special orders.

From now until the end of September (9/30/09) take 10% off your purchase from our website

www.glassartmoldsandsupplies.com/

by entering this code at checkout: 61BLOG

Follow us on Twitter: www.twitter.com/GlassArtSupply.

Be sure to tell your friends and share the fun!